Omron C200HS Instrukcja Użytkownika Strona 408
- Strona / 504
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
399
10-6 Host Link Errors
These error codes are received as the response code (end code) when a com-
mand received by the C200HS from a host computer cannot be processed. The
error code format is as shown below.
@ XX
↵:
XX
XXXX
Node
no.
Header
code
TerminatorFCSEnd code
The header code will vary according to the command and can contain a subcode
(for composite commands).
End
code
Contents Probable cause Corrective measures
00 Normal completion --- ---
01 Not executable in RUN mode The command that was sent can-
not be executed when the PC is in
RUN mode.
Check the relation between the
command and the PC mode.
02 Not executable in MONITOR mode The command that was sent can-
not be executed when the PC is in
MONITOR mode.
0B Not executable in PROGRAM
mode
The command that was sent can-
not be executed when the PC is in
PROGRAM mode.
This code is not presently being
used.
13 FCS error The FCS is wrong. Either the FCS
calculation is mistaken or there is
adverse influence from noise.
Check the FCS calculation method.
If there was influence from noise,
transfer the command again.
14 Format error The command format is wrong. Check the format and transfer the
command again.
15 Entry number data error The areas for reading and writing
are wrong.
Correct the areas and transfer the
command again.
16 Command not supported The specified command does not
exist.
Check the command code.
18 Frame length error The maximum frame length was
exceeded.
Divide the command into multiple
frames.
19 Not executable Items to read not registered for
composite command (QQ).
Execute QQ to register items to
read before attempting batch read.
23 User memory write-protected Pin 1 on C200HS DIP switch is ON. Turn OFF pin 1 to execute.
A3 Aborted due to FCS error in trans-
mit data
The error was generated while a
command extending over more
th f b i
Check the command data and try
the transfer again.
A4 Aborted due to format error in
transmit data
g
than one frame was being execu-
ted.
Nt Th dt t tht ith
g
A5 Aborted due to entry number data
error in transmit data
Note: The data up to that point has
already been written to the ap-
p
ro
p
riate area of the CPU
A8 Aborted due to frame length error
in transmit data
propr
i
a
t
e area o
f
th
e
CPU
.
Other --- Influence from noise was received. Transfer the command again.
Power Interruptions The following responses may be received from the C200HS if a power interrup-
tion occurs, including momentary interruptions. If any of these responses are re-
ceived during or after a power interruption, repeat the command.
Undefined Command Response
@00IC4A*↵
No Response
If no response is received, abort the last command and resend.
Host Link Errors Section 10-6
- Programmable Controllers 1
- Operation Manual 2
- OMRON Product References 3
- Visual Aids 3
- About this Manual: 4
- TABLE OF CONTENTS 5
- Table of contents 11
- PRECAUTIONS 13
- 1 Intended Audience 14
- 2 General Precautions 14
- 3 Safety Precautions 14
- 5 Application Precautions 15
- Conformance to EC Directives 16
- Section 6 16
- SECTION 1 17
- Introduction 17
- 1-1 Overview 18
- 1-2 The Origins of PC Logic 18
- 1-3 PC Terminology 19
- 1-4 OMRON Product Terminology 19
- 1-5 Overview of PC Operation 20
- 1-6 Peripheral Devices 21
- 1-7 Available Manuals 21
- 1-8 New C200HS Features 22
- 1-8-2 Faster Execution Times 23
- 1-8-3 Larger Instruction Set 24
- 1-8-11 Peripheral Devices 26
- 1-8-12 Using C200H Programs 27
- Memory Cassette to the CPU 29
- SECTION 2 30
- Hardware Considerations 30
- 2-1 CPU Components 31
- 2-1-1 CPU Indicators 32
- 2-2 PC Configuration 33
- 2-4 Memory Cassettes 36
- Metal bracket 37
- 2-6 CPU DIP Switch 38
- SECTION 3 39
- Memory Areas 39
- 3-1 Introduction 40
- 3-2 Data Area Structure 41
- 3-8 TC Area 42
- 3-3 IR (Internal Relay) Area 45
- IR Area Section 3-3 46
- 3-4 SR (Special Relay) Area 47
- SR Area Section 3-4 48
- 3-4-2 Remote I/O Systems 53
- Host Link Systems 54
- PC Link Systems 54
- 3-4-4 Forced Status Hold Bit 55
- 3-4-5 I/O Status Hold Bit 56
- 3-4-6 Output OFF Bit 56
- 3-4-8 Low Battery Flag 56
- 3-4-9 Cycle Time Error Flag 57
- 3-4-11 First Cycle Flag 57
- 3-4-12 Clock Pulse Bits 57
- 3-4-13 Step Flag 58
- 3-4-14 Group-2 Error Flag 58
- 3-4-17 Arithmetic Flags 58
- 3-4-21 Memory Cassette Areas 60
- 3-4-24 Memory Error Flags 61
- 3-4-25 Data Save Flags 61
- 3-4-26 Transfer Error Flags 62
- 3-4-27 PC Setup Error Flags 62
- AR Area Section 3-5 63
- 3-5-2 Slave Rack Error Flags 64
- 3-5-3 Group-2 Error Flags 64
- 3-5-6 Error History Bits 65
- 3-5-7 Active Node Flags 66
- 3-5-10 TERMINAL Mode Key Bits 67
- :DM 0100 69
- RESETSET 70
- EXT MONTR 70
- 3-6-3 Error History Area 71
- DM Area Section 3-6 73
- 3-7 HR (Holding Relay) Area 74
- 3-8 TC (Timer/Counter) Area 74
- 3-9 LR (Link Relay) Area 75
- 3-10 UM Area 75
- SECTION 4 76
- 4-1 Basic Procedure 77
- 4-2 Instruction Terminology 77
- 4-3 Program Capacity 78
- 4-4 Basic Ladder Diagrams 78
- Instruction 79
- 00000 00100 LR 0000 81
- 4-4-4 OUTPUT and OUTPUT NOT 83
- 4-4-5 The END Instruction 83
- 00000 00001 85
- 4-5 The Programming Console 91
- 4-6 Preparation for Operation 93
- 4-6-1 Entering the Password 94
- 4-6-2 Buzzer 94
- 4-6-3 Clearing Memory 95
- 4-6-5 Clearing Error Messages 98
- 4-6-6 Verifying the I/O Table 99
- 4-6-7 Reading the I/O Table 100
- Meaning of Displays 101
- 4-6-8 Clearing the I/O Table 102
- 4-7-3 Checking the Program 109
- 4-8 Controlling Bit Status 110
- Section 5 Instruction Set 110
- 4-7-5 Program Searches 112
- Original Program 114
- Diagram A: Correct Operation 116
- 5-10 INTER 119
- 4-7-8 Jumps 120
- 4-8-2 KEEP 122
- 00002 00003 123
- 00004 00005 123
- Work Bits Section 4-9 124
- 4-10 Programming Precautions 125
- AND LOAD and OR LOAD 126
- 4-11 Program Execution 127
- SECTION 5 128
- Instruction Set 128
- 5-1 Notation 131
- 5-2 Instruction Format 131
- ∗DM 0001 132
- 5-5 Expansion Instructions 133
- Section 4 Writing 135
- 5-7 Instruction Set Lists 138
- 4-4-3 Ladder Instructions 142
- 5-9 Bit Control Instructions 143
- IR, AR, HR, LR 144
- 5-23 Subroutines and Inter 145
- 5-9-4 KEEP – KEEP(11) 146
- 4-8-3 Self-maintain 147
- 5-10 INTERLOCK – 147
- 5-14-1 TIMER – TIM 148
- N: Jump number 150
- # (00 to 99) 150
- 5-12 END – END(01) 151
- 5-13 NO OPERATION – NOP(00) 151
- 5-14-4 COUNTER – CNT 153
- 5-14-4 COUNTER 154
- 5-9-4 KEEP – 154
- KEEP(11) 154
- N: TC number 156
- # (000 through 015 preferred) 156
- SV: Set value (word, BCD) 156
- IR, AR, DM, HR, LR, # 156
- # (000 through 511) 161
- 5-15 Data Shifting 163
- Data Shifting Section 5-15 164
- 5-15-5 ROTATE LEFT – ROL(27) 168
- 5-15-6 ROTATE RIGHT – ROR(28) 168
- 5-15-9 WORD SHIFT – WSFT(16) 170
- ASFT(17) 171
- 5-16-1 MOVE – MOV(21) 172
- 5-16-2 MOVE NOT – MVN(22) 172
- 5-16-3 BLOCK SET – BSET(71) 173
- Data Movement Section 5-16 174
- DIST(80) 176
- IR, SR, AR, DM, HR, TC, LR, # 177
- COLL(81) 179
- 5-16-9 MOVE DIGIT – MOVD(83) 180
- XFRB(62) 182
- MCMP(19) 183
- Data Comparison Section 5-17 184
- BCMP(68) 188
- TCMP(85) 189
- 5-18 Data Conversion 193
- Data Conversion Section 5-18 194
- @HEX(––) 211
- LINE(63) 213
- COLM(64) 214
- 5-19 BCD Calculations 217
- 5-19-3 SET CARRY – STC(40) 218
- 5-19-4 CLEAR CARRY – CLC(41) 218
- 5-19-5 BCD ADD – ADD(30) 218
- BCD Calculations Section 5-19 219
- 5-19-7 BCD SUBTRACT – SUB(31) 220
- 5-19-9 BCD MULTIPLY – MUL(32) 224
- 5-19-11 BCD DIVIDE – DIV(33) 225
- 5-20 Binary Calculations 232
- Mi – Su – CY CY R 234
- MBSL(––) 244
- DBSL(––) 246
- 5-21-2 FIND MINIMUM – MIN(––) 247
- 5-21-4 SUM – SUM(––) 250
- @SUM(––) 252
- Examples 253
- 5-21-6 PID CONTROL – PID(––) 255
- 1, 2, 3 261
- 5-22 Logic Instructions 262
- 5-22-2 LOGICAL AND – ANDW(34) 263
- 5-22-3 LOGICAL OR – ORW(35) 264
- 5-23-1 Subroutines 266
- 5-23-2 Interrupts 267
- Interrupt mode 268
- (1 = high-speed) 268
- N: Subroutine number 270
- 00 to 99 270
- 5-23-5 MACRO – MCRO(99) 273
- 3-6-4 PC Setup 276
- 5-24 Step Instructions 279
- Step controlled by LR 2000 280
- Step controlled by LR 2001 280
- 5-25 Special Instructions 288
- 5-25-2 CYCLE TIME – SCAN(18) 289
- LSS Operation Manual 290
- Appendix 291
- FAL(06) 00 292
- TERM(48) 294
- 6-1 Cycle Time 295
- 00000 00002 299
- 00001 00003 299
- Diagnostic 299
- @SRCH(––) 303
- @XDMR(––) 304
- SEND(90) 305
- Control Data 306
- RECV(98) 307
- SYSMAC LINK System Manual 308
- SEND(90)/RECV(98) Enable Flag 309
- SEND(90)/RECV(98) Error Flag 309
- 5-27-1 RECEIVE – RXD(––) 310
- 5-27-2 TRANSMIT – TXD(––) 312
- 0123456789101112 316
- Input Unit 322
- Output Unit 322
- 5-28-5 MATRIX INPUT – MTR(––) 326
- B0B1B2B3B4B5B6B7B8B9 327
- A0A1A2A3A4A5A6A7A8A9 327
- A0A1A2A3A4A5A6A7A8 327
- SECTION 6 329
- Program Execution Timing 329
- Cycle Time Section 6-1 331
- 6-3 Instruction 332
- Execution Times 332
- 6-2 Calculating Cycle Time 334
- 6-2-2 PC with Link Units 335
- ÷ constant → word 339
- ÷ word→ word 339
- ÷ :DM → :DM 339
- ÷ word → word (equals 0) 341
- 6-4 I/O Response Time 345
- 6-4-2 Remote I/O Systems 346
- RT + TTT 347
- 6-4-3 Host Link Systems 348
- PC Link Unit 349
- I/O Response Time Section 6-4 350
- SECTION 7 356
- 7-1-1 Bit/Word Monitor 357
- 7-1-2 Forced Set/Reset 360
- 7-1-3 Forced Set/Reset Cancel 362
- Word currently 363
- [ Data ] 363
- 7-1-8 Differentiation Monitor 368
- 7-1-9 3-word Monitor 369
- 7-1-11 Binary Monitor 370
- Indicates Force Reset 371
- Indicates Force Set 371
- (Force Status Clear) 372
- IR bit 00115 IR bit 00100 373
- Returns to original display 375
- Current SV (during 375
- SV before the change 375
- 7-1-15 UM Area Allocation 377
- 7-1-18 Keyboard Mapping 379
- SECTION 8 383
- Communications 383
- 8-1 Introduction 384
- Section 8-2 385
- 8-2-3 Wiring Ports 387
- 00100 SR 26405 389
- 8-2-7 NT Links 394
- SECTION 9 395
- Memory Cassette Operations 395
- 9-1 Memory Cassettes 396
- 9-3 UM Area Data 397
- 9-4 IOM Area Data 398
- IOM Area Data Section 9-4 399
- SECTION 10 400
- Troubleshooting 400
- 10-1 Alarm Indicators 401
- 10-4 Error Messages 401
- Error Messages Section 10-4 402
- Remote I/O 403
- Master Unit number 403
- Rack no 404
- 10-5 Error Flags 406
- Error Flags Section 10-5 407
- 10-6 Host Link Errors 408
- SECTION 11 409
- Host Link Commands 409
- 11-1 Communications Procedure 410
- Command and Response Formats 412
- Section 11-2 412
- 11-2-2 Commands from the PC 414
- 11-3 Host Link Commands 415
- 11-3-3 HR AREA READ –– RH 416
- 11-3-4 PV READ –– RC 416
- 11-3-5 TC STATUS READ –– RG 417
- 11-3-6 DM AREA READ –– RD 417
- 11-3-7 AR AREA READ –– RJ 418
- 11-3-8 IR/SR AREA WRITE –– WR 418
- 11-3-9 LR AREA WRITE –– WL 419
- 11-3-10 HR AREA WRITE –– WH 419
- 11-3-11 PV WRITE –– WC 420
- 11-3-12 TC STATUS WRITE –– WG 420
- 11-3-13 DM AREA WRITE –– WD 421
- 11-3-14 AR AREA WRITE –– WJ 421
- 11-3-15 SV READ 1 –– R# 422
- 11-3-16 SV READ 2 –– R$ 423
- 11-3-17 SV READ 3 –– R% 424
- 11-3-18 SV CHANGE 1 –– W# 425
- 11-3-19 SV CHANGE 2 –– W$ 425
- 11-3-20 SV CHANGE 3 –– W% 426
- 11-3-21 STATUS READ –– MS 427
- 11-3-22 STATUS WRITE –– SC 428
- 11-3-23 ERROR READ –– MF 429
- 11-3-24 FORCED SET –– KS 430
- 11-3-25 FORCED RESET –– KR 431
- Section 11-3 432
- 11-3-28 PC MODEL READ –– MM 433
- 11-3-29 TEST–– TS 434
- 11-3-30 PROGRAM READ –– RP 434
- 11-3-31 PROGRAM WRITE –– WP 435
- 11-3-34 ABORT –– XZ 437
- 11-3-35 INITIALIZE –– :: 438
- 11-4 Host Link Errors 439
- Appendix A 440
- C200H Standard I/O Units 441
- C200H Special I/O Units 442
- C200H Link Units 443
- Optional Products 444
- Link Adapters 445
- Appendix AStandard Models 446
- Standard Models Appendix A 447
- Programming Devices 448
- Training Materials 448
- Appendix B 449
- Expansion Instructions 452
- Appendix C 455
- Appendix D 459
- Appendix DMemory Areas 460
- DM Area (Error Log) 465
- Appendix E 466
- Appendix EPC Setup 467
- Appendix F 470
- I/O Bits 471
- Work Bits 472
- Data Storage 473
- Timers and Counters 474
- Appendix G 475
- Program Coding Sheet 476
- Appendix H 477
- Signed Binary Data 478
- Space 0 @ P ‘ p 0 @ P ‘ p 479
- Glossary 480
- Revision History 496
- TTIM(120): 5−1 to 5−14 145 504
Powiązane produkty i podręczniki dla Nie Omron C200HS
Nie Omron C200H-LK401 Instrukcja Użytkownika
(86 strony)
(86 strony)
Nie Omron F3S-B Instrukcja Użytkownika
(20 strony)
(20 strony)
Nie Omron BF510 Instrukcja Użytkownika
(16 strony)
(16 strony)
Nie Omron NS10-V2 Instrukcja Użytkownika
(13 strony)
(13 strony)
Nie Omron NE-C30-E Instrukcja Użytkownika
(36 strony)
(36 strony)
Nie Omron 3G3MX2 Instrukcja Użytkownika
(16 strony)
(16 strony)
Nie Omron hja-306 Instrukcja Użytkownika
(22 strony)
(22 strony)
Nie Omron ZS-MDC Instrukcja Użytkownika
(94 strony)
(94 strony)
Nie Omron HCG-801 Instrukcja Użytkownika
(56 strony)
(56 strony)
Nie Omron HCG-801 Instrukcja Użytkownika
(128 strony)
(128 strony)
Nie Omron D4BL Instrukcja Użytkownika
(16 strony)
(16 strony)
Nie Omron CX Pro Instrukcja Użytkownika
(12 strony)
(12 strony)
Nie Omron NE-U22V Instrukcja Użytkownika
(72 strony)
(72 strony)
Nie Omron BF500 Instrukcja Użytkownika
(47 strony)
(47 strony)
LG GSL545PVYV podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Lodówki z zamrażarkami LG GSL545PVYV.
Dostarczamy 1 pdf podręczników LG GSL545PVYV do pobrania za darmo według typów dokumentów: Instrukcja Właściciela
Lg GSL545PVYV Instrukcja Właściciela (38 strony)
Marka: Lg | Kategoria: Side-by-side fridge-freezers | Rozmiar: 3.51 MB |
Spis treści
Więcej produktów i instrukcji dla Lodówki z zamrażarkami LG
| Modele | Rodzaj dokumentu |
|---|---|
| LFD22786ST |
Instrukcja Właściciela
LG LFD22786ST side-by-side refrigerator,
43 strony
|
| GSB325NSQV |
Instrukcja Instalacji
LG GSB325NSQV User manual,
10 strony
|
| GSL545NSYZ |
Instrukcja Właściciela
LG GSL325PVCV Datasheet,
38 strony
|
| GW-L227NLYV |
Instrukcja Właściciela
LG GS3159AVJV Owner's manual,
38 strony
|
| GR-F258UTK |
Podręcznik Użytkownika
LG GR-F258UTK User manual,
36 strony
|
| LFC22770SW |
Instrukcja Właściciela
LG LFC22770SW side-by-side refrigerator,
46 strony
|
| GR-D257SL |
Instrukcja Użytkownika
LG GR-D257SL Owner's manual,
40 strony
|
| GSJ976NSBZ |
Instrukcja Użytkownika
LG GSJ976NSBZ User manual [en] [it] ,
41 strony
|
| GP-5D906BSL |
Instrukcja Użytkownika
LG GP-5D906BSL Specification,
2 strony
|
| LFXS24623S |
Instrukcja Właściciela
LG LFXS24623S Owner's manual,
44 strony
|
| LMXS30776S |
Instrukcja Właściciela
LG LMXS30776S Owner's manual,
61 strony
|
| LFXS29766S |
Instrukcja Właściciela
LG LFXS29766S Owner's manual,
61 strony
|
| LFXS29626S |
Instrukcja Właściciela
LG LFXS29626S Owner's manual,
59 strony
|
| GR-N319LLW |
Instrukcja Użytkownika
LG GR-N319LLW Owner's manual,
32 strony
|
| GF-SD730SL |
Instrukcja Użytkownika
LG GF-SD730SL Specification,
2 strony
|
| GF-5D906SL |
Instrukcja Użytkownika
LG GF-5D906SL Specification [de] [en] [fr] [it] [nl] ,
2 strony
|
| GB-W450UPLX |
Instrukcja Użytkownika
LG GB-W450UPLX Specification,
2 strony
|
| LFXS24623D |
Instrukcja Właściciela
LG LFXS24623D Owner's manual,
44 strony
|
| GB-450UPLE |
Instrukcja Użytkownika
LG GB-450UPLE Specification,
2 strony
|
| LFXS24663S |
Instrukcja Właściciela
LG LFXS24663S Owner's manual,
45 strony
|
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji